Tafel 7 Vergaser ES BVF

Repair sentence for carburettor BVF 25,5KN1-2.
The set includes:

- main jet 105
- needle jet 2,70
- part load needle number 3
- float needle
- 4 fiber gaskets
- valve insert gasket

Made in Germany.

DETAILS

Repair sentence for carburettor BVF 28.5 KN1-1 and similar names.
The set includes:

- main jet 105
- needle jet 2,67
- part load needle number 11
- float needle
- 4 fiber gaskets
- valve insert gasket

Made in Germany.

DETAILS

Repair sentence for carburettor BVF 28.5 KN1-1 and similar names.
The set includes:

- main jet 120
- needle jet 2,77
- part load needle
- float needle
- 4 fiber gaskets
- valve insert gasket, mixing chamber gasket

Made in Germany.

DETAILS

DETAILS

Der Kraftstoffsystemreiniger speziell für Zweiräder mit 2- und 4-Takt-Motoren. Verschmutzungen wie zum Beispiel Verkokungen im Brennraum, Verharzungen im Vergaser, Verklebungen der Einspritzdüsen, Kondenswasser im Kraftstoffsystem werden zuverlässig entfernt. Hochwirksame Schmierkomponenten schützen das Kraftstoffsystem während des Reinigungsvorganges und verhindern die Ablagerung gelöster Partikel. Ein sauberes Kraftstoffsystem ist Voraussetzung für eine saubere und wirkungsvolle Verbrennung. Es gibt dem Motor die beste Performance für eine kraftvolle Leistungsentfaltung, ruckelfreien Betrieb, verbesserte Leistung, deutliche Kraftstoffersparnis, längere Lebensdauer der Komonenten des Kraftstoffsystems und es stabilisiert den Kraftstoff.[TAB:Anwendung]Eine Dose Fuel System Clean sollte bei längeren Standzeiten (Überwinterung) und regelmäßig alle 6 Monate dem Kraftstoff vor der Betankung zugegeben werden.[TAB:Warnhinweise]

• Flüssigkeit und Dampf leicht entzündbar
• nicht in die Augen, auf die Kleidung oder die Haut gelangen lassen
• verursacht Haut- und schwere Augenreizungen
• bei Kontakt mit der Haut - mit viel Wasser und Seife waschen
• kann Schläfrigkeit und Benommenheit verursachen
• kann bei Verschlucken und Eindringen in die Atemwege tödlich sein
• bei Verschlucken SOFORT Giftinformationszentrum oder Arzt anrufen (Verpackung oder Etikett bereithalten)
• kein Erbrechen herbeiführen
• schädlich für Wasserorganismen, mit langfristiger Wirkung
• von Hitze, Funken, offener Flamme, heißen Oberflächen o.ä. fernhalten
• Einatmen von Staub, Rauch, Gas, Nebel, Aerosol vermeiden - nicht rauchen
• nur im Freien oder in gut belüfteten Räumen verwenden und nach Gebrauch Hände gründlich waschen
• Freisetzung in die Umwelt vermeiden
• Darf nicht in die Hände von Kindern gelangen

DETAILS

DETAILS

MZA-Artikelnr.:   74193A    

Neuer Blechschwimmer mit Spange passend für MZ ES175, ES175/1, ES250, ES250/1 und ES300 mit Vergaser N271-0, N261-7, 27 KN 1-1, 25,5 KN 1-1. Durchmesser: 42,3 mm, Höhe ca. 37mm. Deutsche Fertigung.
DETAILS

MZ Nummer: 2259

Neuer Blechschwimmer mit Spange passend für MZ ES175, ES175/1, ES250, ES250/1 und ES300 mit Vergaser N271-0, N261-7, 27 KN 1-1, 25,5 KN 1-1. Durchmesser: 41 mm, Höhe ca. 37mm. Deutsche Fertigung.
DETAILS

MZ Nummer: 2259

MZA-Artikelnr.:   16368-A-M    

New carburettor Bing for MZ IT 250 and IT 250/1. These carburettors are produced as a substitute of the genuine parts. In the processing and behaviour these are to the original consider. The carburettor is regulated well and stop. He is delivered ready with installation and preset. The carburettor is produced by us from a standard carburettor. He is not available therefore in trade. And is made as a substitute with the original BVF. As the only you must change the starter pull. The external casing is too long and must be shortened. For a surcharge of 6.85? if you can coorder such a Bowden cable. The installation is also easy for the "nonexpert" and is uncomplicated. A low consumption and a very easy setting are the biggest advantages of this carburettor. The engine promptly reacts to the smallest change of the settings. Thereby you can seat easily bigger nozzles, for example, to the increase in output. The processing is exemplary and exact. The springs are strong and from the best spring steel. The work-sided opposed float situation please do not change; you can change all the other settings fast, but please only gradually. Technical data: - Bing bar carburettor 84/30/110, anew, made in Germany connection Putting in the suction connecting piece to the cylinder, 35 mm - connection air filter 45 mm - passage 30 mm - for 1-cylinder 2-cycle - main nozzle 118 (corresponds to the original with 250 cubic centimetres). Scope of supply: - (With it you can reorder carburettor as described, preset - exploded view with spare part list - installation instructions - data sheet and description - unique service number still after years). - 2-year guarantee on material and manufacturers mistake, except wear - It are necessary no rebuildings in your MZ. With some models the external cover in the starter pull must be shortened, all the other parts, tackles and connections fit.

DETAILS

MZA-Artikelnr.:   16368-A-M    

New carburettor Bing for all MZ with 250 cubic centimetres of cubic capacity. Special in this model is the clamp connection. With all ES250 / 1 the carburettor on the connecting piece was put to the cylinder. Besides, the external diameter of the connecting piece amounts serially to 35 mm. However, this connecting piece became used also (even if seldom) with the TS250 or models ETZ250. These carburettors are produced as a substitute of the genuine parts and are modified by us. In the processing and behaviour these are to the original consider. The carburettor is regulated well and stop. He is delivered ready with installation and preset. There is this model not to shop in this issue, otherwise. Also as a substitute with carburettor BVF. As the only you must change the starter pull. The external casing is too long and must be shortened. For a surcharge of 6.85€ you can coorder such a Bowden cable. The installation is also easy for the "nonexpert" and uncomplicated.i A low consumption and a very easy setting are the biggest advantages of this carburettor. The engine promptly reacts to the smallest change of the settings. Thereby you can seat easily bigger nozzles, e.g., to the increase in output. The processing is exemplary and exact. The springs are strong and from the best spring steel. The work-sided opposed float situation please do not change; you can change all the other settings fast, but please only gradually. Technical data: - Bing bar carburettor 84/30/110 K, anew, made in Germany - clamp connection on the suction connecting piece to the cylinder, 35 mm - connection air filter 52 mm - passage 30 mm - for 1-cylinder 2-cycle - main nozzle 118 (corresponds to the original with 250 cubic centimetres). Scope of supply: - (With it you can reorder carburettor as described, preset - exploded view with spare part list - installation instructions - data sheet and description - unique service number still after years). - 2-year guarantee on material and manufacturers mistake, except wear - It are necessary no rebuildings in your MZ. With some models the external cover in the starter pull must be shortened, all the other parts, tackles and connections fit. The carburettor cover with ES - to models must be filed something, then this fits again!

DETAILS

MZA-Artikelnr.:   Mza    

New carburettor Bing for all MZ with 300 cubic centimetres of cubic capacity. Special in this model is the clamp connection. With all ES300 / 1 the carburettor on the connecting piece was put to the cylinder. Besides, the external diameter of the connecting piece amounts serially to 35 mm. These carburettors are produced as a substitute of the genuine parts and are modified by us. In the processing and behaviour these are to the original consider. The carburettor is regulated well and stop. He is delivered ready with installation and preset. There is this model not to shop in this issue, otherwise. Also as a substitute with carburettor BVF. As the only you must change the starter pull. The external casing is too long and must be shortened. For a surcharge of 6.85? if you can coorder such a Bowden cable. The installation is also easy for the "nonexpert" and is uncomplicated. A low consumption and a very easy setting are the biggest advantages of this carburettor. The engine promptly reacts to the smallest change of the settings. Thereby you can seat easily bigger nozzles, e.g., to the increase in output. The processing is exemplary and exact. The springs are strong and from the best spring steel. The work-sided opposed float situation please do not change; you can change all the other settings fast, but please only gradually. Technical data: - Bing bar carburettor 84/30/110-K1, anew, made in Germany - clamp connection on the suction connecting piece to the cylinder, 35 mm - connection air filter 52 mm - passage 30 mm - for 1-cylinder 2-cycle - main nozzle 125 (corresponds to the original with 300 cubic centimetres). Scope of supply: - (With it you can reorder carburettor as described, preset - exploded view with spare part list - installation instructions - data sheet and description - unique service number still after years). - 2-year guarantee on material and manufacturers mistake, except wear - It are necessary no rebuildings in your MZ. With some models the external cover in the starter pull must be shortened, all the other parts, tackles and connections fit. The carburettor cover with ES - to models must be filed something, then this fits again!

DETAILS